PeteNetLive - KB923 - Configure Wireless Network Settings via

Where to find wireless Network Settings?

Router In Computer Network / January 3, 2017

gateway ip camOnce you have the Foscam IP Camera setup and connected via ethernet/network cable, please follow the steps below to set it up wirelessly:

1) Most importantly, ensure you are running your wireless network on the 802.11b/g/n standard at 2.4GHz. Some 802.11n will run on 5GHz which is not compatible with our cameras. Please refer to your router’s manual on how make this setting change if necessary.

2) Find and note down the following information about your wireless network:
a) SSID (Name of the wireless network)
b) Share key (Password to join the wireless network)

If you do not know this information, you will need to log in to your wireless router. To do this enter the IP address of your router into your browser and press enter. You will be prompted to enter your router username and password. If you do not know the IP address of your router you can view it in IP CAMERA TOOLS by selecting and right clicking on your camera, selecting “Network Configuration”, and noting down the “Default Gateway” IP address. This Default Gateway IP address is the the IP address of your router.

If you cannot figure out your username, password or the IP address of your router, refer to your router’s manual. If you don’t have the manual on hand, you can obtain a list of default router IP addresses, usernames and passwords by going to our blogpost here.

Please Note: Not all routers are the same and your router will likely look different.

Once logged in to your router look for an option called “Wireless Settings” or “Wireless LAN”. Once in the Wireless Settings look for and jot down what you have for the setting called “SSID”. Next, look for the setting “Wireless Mode” and make sure it is set to 2.4GHz. Next, look under the “Security Settings” under “Wireless Settings’ and jot down the “Encryption Method”, “Encryption Technique” and the “Shared Key”. In our example, the “Encryption Method” and “Encryption Technique” is not shown and the “Wireless Settings” section contains the “Security Settings”.

Wireless Settings3) Once you have the information about your network listed in step 2, log in to your camera while it is connected with the ethernet cable. To do this, open IP camera tools and double click on your camera, or enter your camera’s local IP address into your broswer. On the login page, enter the username and password for the camera (default username: “admin” / password: ” ” – leave password blank) and press “Login”.

You will notice that there are three different options: “ActiveX”, “Server Push”, and “Mobile Phone”. These options correspond to the browser being used. If Internet Explorer is being used, use the “ActiveX” option. If Mozilla Firefox or Google Chrome is being used, use the “Server Push” option. If a supported mobile device is being used, use the “Mobile Phone” option.

4) Once logged in to the Camera, look on the left panel and click on the option “For Administrator” (if using IE) or “Device Management” (if using Firefox or Google Chrome”). Then click on “Wireless Lan Settings”. Here, check the box next to “Using Wireless LAN”.

Next, click the “Scan” button and wait for the countdown to finish. The page will refresh and should show a list of networks. Please select the network that has your “SSID”. The fields should auto-populate leaving only the “Share Key” blank. If you are not in the same area as your network then, enter your “SSID” and select your “Encryption” which is going to be (e.g., WPA/WPA2/WEP together with either TKIP/AES/TKIP-AES). Next, enter your “Shared Key”. Click “Submit” and let the Camera Reboot. Wait 30 seconds and then remove the ethernet/network cable.

If you are having trouble, set your wireless Encryption Method to WPA and your encryption technique to TKIP. I seem to have the best results using those settings.

5) Give the camera about 30 to 45 seconds to start up and you should start to see the green led on the back flashing much faster. Open IP camera tools and the camera should appear. Once your camera goes wireless your camera will receive a new IP Address, you will need to use this new IP Address when setting up port forwarding. Now that you have the Wireless Setup working on your Foscam IP Camera, then you can go on to the next tutorial which shows you how to setup your Foscam so that it is accessible from anywhere on the internet.
Please continue on to the Guide To Setting Up Port Forwarding for Viewing Your Foscam Wireless Camera Over the Internet

Source: foscam.us